Ruwido easytip series Manuel d'utilisateur télécharger pdf (Page 2)

UNIVERSAL REMOTE CONTROL

Thank you for purchasing this universal remote control. Before using the remote you will need to

insert 2 type „AAA“ batteries (not included) in the battery compartment ensuring that you follow the

polarity shown on the inside. You can now use your remote control to operate your TV cabo box and

your TV.

Operation of the TV cabo box

Press the TV cabo key in order to operate your TV cabo box. Please refer to the TV cabo manual for

TV cabo functions.

Easy programming for the control of your TV SET

1. Insert 2 new 1.5V alkaline batteries of type „AAA/LR03“. Observe battery polarity as indicated in

the battery compartment.

2. Switch on your TV SET.

3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).

4. Beside the manufacturer’s name, you will find one or more 3-digit codes. These codes must be

entered into the remote to enable it to work with your particular TV set.

5. Press the key on the remote control for approximately 4 seconds until the LED flashes

twice.

6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the list.

7. After entering the code the LED will flash twice indicating that the code has been accepted.

8. Point the remote control towards your TV and press the key. If your TV does not respond by

going into Stand-By mode then repeat steps 3 to 8 and enter the next code in the list.

9. If your TV goes into Stand-By mode when the key pressed then your remote control has

found a compatible code. Next test all of the other function buttons. If certain functions are not

working correctly then restart the process moving onto the next code number as this may well

improve the situation.

10. If the codes in the list fail to operate your TV then next move onto the automatic code scan

function (see below).

Code scan

If programming using the codes in the enclosed list failed to work then you must next try the

automatic code scan.

A. Ensure that the remote control is equipped with 2 new batteries (see step one of easy

programming procedure).

B. Switch on your TV SET.

C. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

D. After seeing the 2 flashes and within 5 seconds, enter the code . After entering the code

the LED will flash twice indicating that the code has been accepted

E. Press and hold the key until your TV switches off. Please note that this process might take

up to 15 minutes. During the automatic scanning you can remove your finger or change hands

provided it is replaced within 8 seconds. If left off of the key for more than 8 seconds then the

remote will revert back to its normal mode. If your TV switches into Stand-By mode during the

automatic process then immediately remove your finger from the key and then press the

key until the LED flashes twice, this will then store the code that the remote control has

found.

F. In some cases during the automatic scanning search the remote control might find several codes

that appear to operate your TV etc, however, if some of the buttons fail to work properly then it’s

possible the remote has found a partially compatible code. In such cases you will need to restart

the automatic scanning process (steps B. to F.) until a better code is found. Please note that

once the automatic process is restarted, the remote continues from the last stored code and not

at the beginning of code database.

Finding out what code number you are using

If you have programmed your remote control by means of the automatic code scan, or if you have

forgot the code you have stored then the following procedure

will replay the codes being used.

A. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

B. Enter code , using the numerical keys. The LED flashes twice.

C. Press key and count the number of LED flashes. This number corresponds to the first digit of

the code.

D. Press key and count the number of LED flashes. This number corresponds to the second

digit of the code (if the digit is 0, the LED does not flash).

E. Press key and count the number of LED flashes. This number corresponds to the third digit of

the code (if the digit is 0, the LED does not flash).

F. Steps C, D and E can be repeated as often as necessary.

Write down the code number as indicated by the LED.

USER MANUAL

Bed.-Anl. H2 Version1 10.03.2004 16:16 Uhr Seite 2

1 2 3 4 5 6 7 ... 11 12

Commentaires sur ces manuels

Pas de commentaire

Ruwido easytip series Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Télécommandes Ruwido easytip series